System Configuration
17
System Setup4. Turn the AVR65 on either by pressingwarranty, and may not be covered by the
Once the speakers have been placed in thethe System Power Control2onprojector TV setOs warranty. Please consult
room and connected, the final step in thethe front panel, or via the remote bythe ownerOs manual for your video display
setup process is to enter the settings thatfirst pressing the AVR Selectora,for specific information about image
configure the AVR65Os bass managementand then pressing the Power buttonburn-in.
system for the type of speakers used inc. The Power Indicator3will
your system, the calibration of the outputturn green to confirm that the unit isThe AVR65 has two on-screen display
levels and the delay times used by the sur-on, and the Information Display ýmodes, Osemi-OSD� and Ofull-OSD�.
round sound processor. Before proceedingwill also light up.When making configuration adjust-
further, this is a good time to review thements, it is recommended that the full-
installation section of the manual toUsing the On-Screen DisplayOSD mode be used. This will place a
make certain that all connections areWhile configuring the AVR65 so that it iscomplete status report or option listing
properly made.properly matched to the specific speakerson the screen, making it easier to view
in your system, as well as when settingthe available options.
You are now ready to power up the AVR65other system parameters, you may find it
to begin these final adjustments.helpful to take advantage of the unitOsTo view the full-OSD screens, press the
on-screen display system. These easy-to-OSDbutton othree times. The first
1. Plug the Power CableŢ to anread displays give you a clear picture ofpress will bring up the semi-OSD mode
unswitched AC outlet.the current status of the unit, and makeand the second press will turn that mode
it easy to see which speaker, delay, inputoff. The third press will call up the full-
2. Press the Main Power Switch1or digital selection you are making.OSD display (Figure 1).
in so that it latches in with the OOFF�
wording on the top of the switchTo view the on-screen displays, make cer-The display will appear any time a
inside the front panel. Note that thetain you have made a connection fromchange is made to the settings or fea-
Power Indicator3will turnthe TV Monitor Video Outjack a ontures, and it will automatically follow the
amber, indicating that the unit is inthe rear panel to the video input of yourcommand pattern of remote or front
the Standby mode.TV, projector or display device. In order topanel instruction. It is not necessary to
view the displays, the video source must beuse any other navigation buttons to use
3. Install the four supplied AAA batteriesselected as described in the instructions forthe AVR65Os On-Screen Display system.
in the remote as shown. Be certain tothe video display.
observe the (+) and (�) polarityNote that the full screen displays will
indicators shown in the bottom of theNOTE: The AVR65Os on-screen displaystime-out after 30 seconds. However, the
battery compartment.may only be viewed when the standard,on-screen display used with the channel
composite video output is in use. The dis-output level adjustments will remain on
plays are NOT visible when the S-Videothe screen as long as the settings are
signal is displayed.being changed. This display must be
manually turned of by pressing the OSD
IMPORTANT NOTE: When viewing button o.
the displays on a projection TV it is
important that they not be left on the AUDIO SOURCE :DVD
VIDEO SOURCE :DVD
screen for an extended period of time. As AUDIO INPUT :ANALOG
TAPE MONITOR : OFF ON
with any video display, but particularly
with projectors, constant display of a static SURR. MODE :PRO LOGIC
image such as these menus or video game MULTI ROOM : OFF ON
images may cause the image to be perma- MASTER VOLUME:�19DB
nently Oburned in� to the CRT. This type
of damage is not covered by the AVR65
Figure 1
AVR65 120 volt Rev (C) 10/6/98 |
ACEC
